You can invoke tracing during or after an ongoing conversation. The external line can be held for a limited period of time. Order Mal. Call Tracing g During an ongoing conversation: Press Note: Function key pre-programmed by system administrator. The system acknowledges with different tones whether the tracing request was accepted or rejected. Headset If your telephone is equipped with Option unit DBY 02, the following headset functions are available. Note: How to install Option unit and headset, see installation instruction provided with the Option unit.
All calls can be handled via the headset. Headset with loudspeaking s 58 and telephones only. Press Press the headset key Note: Function key pre-programmed by system administrator. Handsfree to headset Headset g and telephones only. Press the headset key Note: Function key pre-programmed by system administrator.
The business call will be charged your office extension number or an account number. You will just be charged for the call to the office. Press Enter the authorization code and press Dial tone. Depending on the type of paging system it is possible to send digit messages or voice messages to the paged person. Paging can also be initiated and answered during an ongoing call.
Make an Inquiry call and proceed according to the appropriate procedure for the type of connected paging system. You can then either return to the ongoing call or transfer the paging call to the person that was put on hold. If this person is an external subscriber, your exchange must be programmed for this function.
If you receive a congestion tone when paging, this indicates that the paged person has his paging receiver in the charging rack and is probably out of the office. If you want to start paging without calling the person: Press Dial the extension number and press Wait for an answer with the handset off hook. Replace the handset Wait for the paged person to call back. Press Dial the extension number and press Dial the message code 1—10 digits and press Wait for the acknowledgement tone.
Replace the handset If expected, wait for the paged person to call back. If zeros are shown it indicates that you are being paged from an external subscriber. To answer: Press Dial your own extension number and press Or if only one paging call is permitted at the time: Press If a message code is shown in the display, take the appropriate action. Just before the predetermined speech time is ended, a warning tone will be heard.
If you want to start paging without calling the person: Press Dial the extension number and press Leave your message after the tone. To answer If your paging receiver has bothway voice connection, press the answer button to speak. If no bothway connection exists, take the appropriate action according to the message or answer the paging in the same way as paging without a voice message.
Replace the handset Press Dial the extension number and press Dial the message code 1—5 digits and press Wait for the acknowledgement tone.
This function is automatically cancelled when the call is finished. Outgoing calls can be made as usual. Dial to activate Special dial tone. The group can be bypassed by you. Press Special dial tone. Press Bypass Press and dial the extension number Press The call is made to the specified extension in the group. You can use the code for one call only or you can open the phone for some calls and lock it when leaving the phone.
Dial the digit or digits to get an external line and the external number Press Enter authorization code and press Verification tone.
Press Enter authorization code and press Verification tone. You can also temporarily change any other used telephone within the exchange to the same authority level as you have on your own phone. The individual code can be changed from your own extension.
To make calls with your authority level when your telephone is locked Press Enter authorization code and press Verification tone. Dial the digit or digits to get an external line and the external number To open your telephone Press Enter authorization code and press Verification tone.
Dial your own extension number and press Verification tone. Dial the digit or digits to get an external line and the external number Press Enter old authorization code and press Enter new authorization code and press Verification tone. When you want to use the function, just press the key.
Certain functions must be pre-programmed by the system administrator. H g z g H Program or change a function on Dialog Keep pressed while programming Press selected function key Enter telephone number or a function code according to the list in Functions and required data Note: If a wrong number is entered, press the Clear key to erase it, and then enter the number again.
Press the function key again Release Remove the transparent cover and write the function name or telephone number beside the key. Note: To erase a programmed function, press the Clear key, instead of the telephone number or function code, in the sequence above.
Enter telephone number or a function code according to the list in Functions and required data Note: If a wrong number is entered, press the Clear key to erase it, and then enter the number again.
Press the function key again Press to finish programming Remove the transparent cover and write the function name or telephone number beside the key. Verify a programmed number or function on Dialog Program Program g g g Dialog , and Note: This function is only available on the telephone. Press Press selected function key The stored number or function is displayed.
When the function is programmed by you, you will not get a toggle function. Instead you will have one key for activation and another key for deactivation.
The key lamp will not indicate that the function is activated. When the function is programmed by the System Administrator you will get a toggle function and the key lamp will indicate that the function is activated. The different signals can be programmed on access lines, additional lines and multiple represented lines. Note: Options 5 and 6 are not available for multiple represented lines. Press Press the corresponding line key A digit 0—6 is shown in the display telephone only.
Access 1 Program g g X Note: Options 5 and 6 are not available for multiple represented lines. Press Press to finish programming Press to clear the display during programming Note: telephone only. To verify a ringing signal on Dialog Program Access 1 Program g g g Dialog , and Note: This function is only available on the telephone. Press Press the corresponding line key A digit 0—6 is shown in the display.
Note: If you use melodies to signal incoming calls telephone only , this will replace the tone character. H 0—9 H Program Program 78 g 0—9 g Program on Dialog Keep pressed while programming Press the corresponding digit The telephone rings with the chosen character.
Press the corresponding digit The telephone rings with the chosen character. Adjust handset listening volume in handset mode. Adjust loudspeaker volume when the loudspeaker key is activated, e. Press to change the volume Ringing signal volume V Use the volume keys to adjust the ringing signal volume when the telephone is idle or ringing.
Adjusted volume is stored. Press to change the volume Mute ringing signal You can supress the ringing signal for an incoming call. If the Mute key lamp is turned on when you press the key in idle state, your telephone supports this function. Press to supress the ringing signal The ringing signal is switched off for the current call. Incoming calls are only indicated by a flashing access line lamp and display information.
Press to switch off the ringing signal The Mute key lamp is switched on to indicate silent ringing. The ringing signal will automatically be switched on the next time you lift the handset or press any key. Melody ringing telephone only. If you want personal melodies when your telephone rings, you can program one melody to signal an internal call, a second melody for an external call and a third melody to signal a callback call.
Press and hold simultaneously to enter melody mode Melody Mode If there is a stored and activated melody for internal calls Access 1 key , external calls Access 2 key or callback calls Inquiry key , the corresponding key lamp is switched on. Program Access 1 Access 2 Inquiry g g g g V X Program a new melody, edit or delete a current melody Press Program Melody Press the key for the requested type of call: If there is a current melody, the melody is played and the last 19 notes or signs are displayed.
Press for internal calls or Press for external calls or Press for callback calls To edit the current melody: Move the cursor to the right of the position to be edited Keep pressed to go to the beginning or to the end. Press to erase the note to the left of the cursor Keep pressed to erase all the notes. When key lamp is off the stored melody is deactivated. A maximum of 40 notes can be programmed for incoming calls, and 20 notes for recalls. Press to insert a short pause p Hold to get a long pause P.
Repeat to get a longer pause pp Press to move the cursor to the left or to the right Keep pressed to go to the beginning or to the end. Press to listen to the entered notes Press to erase the note to the left of the cursor Keep pressed to erase all the notes. Note: The key to get a sharp or flat tone is pressed after the note, but is displayed before the note.
Tone characteristics The tones shown in this section are the most used tones worldwide. The signals shown in this section are the most used signals worldwide.
Many markets use signals that are adapted for the local standards. If you get a signal that is not described or you cannot identify, ask your system administrator. Steady light The function is active or supervised line is busy. Slowly flashing lamp The line or function is put on hold. Rapidly flashing lamp An incoming call. Light with short breaks Ongoing call. There are two versions of display texts, an earlier and a later version. Both versions are shown in this section.
The display gives you feedback information such as time and date, traffic state and connected telephone numbers. The following displays show examples of the different states your telephone is in. For the later display text version: When an information end with three dots When an information ends with a exclamation mark! Idle telephone When your phone is idle, the upper line shows general information. The lower line shows your extension number. To be changed locally to other languages.
Vocabulary 92 Additional lines One or more additional extension numbers can be assigned to your telephone, these are programmed on free function keys. Idle message A message shown in the display when the telephone is idle. This message is programmed by your system administrator. Multiple represented line Your extension number can be represented on a function key on other extensions two or more. Stair Chair Lift System Needed. Dec MiVoice Digital Phone is a desktop telephone with full functionality for office The Dialog Vision is ideal for demanding … This manual is intended to guide qualified personnel in the installation and operation of this product.
Because of the variety of uses for this equipment and because of the. We will also send you an email with a copy of your Cub Cadet Tractor service manual download link. Find the cheap Bissell Proheat 2x Manual, Find the best Bissell Proheat 2x Manual deals, Amp upright deep cleaner for carpet, upholstery, and stairs Includes a built-in heater, 2-in-1 tank and 12 rows of dual Dirt Lifter power brushes.
Opt in to receive special offers:. Anti-bot validation. Phone System Support. First Name. Your message. Number of phone extensions. System Manufacturer Model. Phone number.
Your Email. Opt in to receive special offers. Key Features 2-line x 20 character display 2 line keys 15 function keys 4 programmable keys Call forward Call transfer Not headset compatible.
We will do all we can to offer our assistance with any problems you may encounter. UK Delivery We aim for next day delivery. Read more information on Delivery. The Customer is required to inspect all goods upon receipt and to notify Office Phone Shop of any defects or complaints within 7 days of receiving goods. It is the responsibility of the customer to ensure the safe return of faulty or incorrect goods to Office Phone Shop.
All goods returned must clearly state customers name, order no, telephone number, fault details and proof of purchasing.
These goods must be in Office Phone Shop's original packaging and condition, with original insertions, fixtures and parts. Failure to do so will result in the refund being invalidated. We use tamper proof labels which are stuck to each item sold by Office Phone Shop.
This ensures that goods have been purchased from Office Phone Shop. When the label is peeled back Office Phone Shop Company details sticks to the glue and the label will then say void. No goods will be accepted back unless this label in intact.
0コメント